background image

1

Attaching & Removing the Turbo

Attaching the Turbo..........................................7
Removing the Turbo ........................................7
Adjustments.....................................................8
Storage ............................................................8
Front Bracket Hole Template ...........................9

Hardware Identification 
& Torque Specifications....................................10

Safety Rules & Information

General Warnings............................................2
Safety Decals ..................................................2

General Operating Information

Before Operation .............................................3
Mowing with the Turbo .....................................3
Operating without the Turbo ............................3
Recommended Accessories............................3
After Operation ................................................3

Initial Setup & Assembly

Prepare Deck, Belt Cover & Support Arm .......4
Install Stacked Arbor Pulley.............................4
Assemble & Install Deflector............................5
Assemble Turbo ...............................................6

Table of Contents

NOTE:  In these instructions, “left” and “right” are
referred to as seen from the operating position.

Summary of Contents for 1694496

















Reviews: