background image

Safety Rules

A

Read these safety 

 the safety rules in 

 Operator’s

Manual and follow them closely. Failure to obey these rules

could result in loss of control of vehicle, severe personal injury

to yourself, or damage to property or equipment. The triangle

in the

text signifies important cautions or warnings which must be followed.

A

WARNING

When blower assembly is removed from mower deck, the deflector

must be installed as described in Operating Without Collection System.

1.

Know the tractor or ridercontrolsand how

to stop quickly. READ THE OWNERS

MANUAL.

2. Disengage the PTO, shut the engine off

and wait for all moving parts to stop before
attaching, adjusting, or disconnecting any
part of the collection system.

3. Check the collection system to make sure

it is bolted tightly to tractor or rider.

4. Check the latch handle to make sure it is

engaged so the dump cart’s box is locked
to the frame.

5.

Look behind to make sure the area is clear

before backing up.

6.

DO NOT turn sharply when the tractor or
rider is alongside a building or any object.

7. DO NOT carry passengers in the cart.

8 .

 CAUTION: 

For added tractor or rider

stability and to prevent tipping or loss of
control;

a. Use reduced speed on uneven ground

and when turning corners.

b. Reduce loads on hillsides. It is rec-

ommended that the collection system
be kept only half full when negotiating

any slopes. Start mowing on slopes
when the collection system is empty.

c. Mow up and down the face of slopes;

never acrossthe face of any slope.

 

 

W h e n   o p e r a t i n g   o n

slopes, use 

 

 Never

operate on slopes greater than 30%
(16.7”).

  A

C A U T I O N

:  

O b j e c t s   m a y   b e   t h r o w n

from mower.

For your safety:

a. DO NOT remove the cover while the

mower blades are 

 Shut off the

engine before 

 the door or

removing the grass chute.

b. Be sure the complete collection

system is in place (cover secure and
g r a s s   c h u t e   c o n n e c t e d )   b e f o r e
operating the mower.

c. DO check the twin bag cover fre-

quently for wear and tear. Replace with

new cover for safety protection.

11. For best results when mowing grass: Set

the mower to cut from 1 to 2 inches of
grass. If grass isexceptionallytall, set your

mower as high as possible for first cutting.
Lower cutting height at succeeding

cuttings until proper height is reached. It

may be necessary to mow tall grass at a

slower tractor speed.

Summary of Contents for 1691810




















Reviews: