background image

7

Features & Controls

*2293

SAFETY INTERLOCK SYSTEM

Your tractor is equipped with a seat switch safety system
that will automatically shut the engine off when the oper-
ator leaves the seat with the ground speed control lever
in gear or with the PTO engaged. Once the engine has
stopped, the electric PTO switch must be turned off after
operator returns to the seat in order to start the engine.

Check the seat switch (A, figure 3) every fall and spring
with the following four tests:

Test 1 - Engine should NOT crank if:

A. seat is not occupied or

B. ground speed control lever out of neutral or

C. PTO lever is engaged.

Test 2 - Engine should crank if:

A. seat is occupied and

B. ground speed control lever is in neutral and

C. PTO lever is disengaged.

Test 3 - Engine should shut off if:

A. operator rises off seat with ground speed control

lever in gear

.

B. operator rises off seat with PTO engaged.

NOTE: If operator returns to seat before engine stops,
the engine will re-start and PTO clutch will re-engage.

Test 4 - PTO will disengage if:

A. operator rises off seat with engine running. 

NOTE: If operator returns to seat before engine stops,
the engine will re-start and PTO clutch will re-engage.

Figure 3. Seat Switch
A. Switch

B. Wiring 

Harness

WARNING

If the tractor does not pass the test, do not oper-
ate tractor. See your authorized dealer. Under no
circumstances should you attempt to defeat the
purpose of the safety system.

A

B

Summary of Contents for 1691219





































Reviews: