background image

4190-9011/9012

Fiber Optic Audio Repeater

Installation/Operation Instructions

 1999 Simplex Time Recorder Co.

All specifications and information shown were current as of publication, and are subject to change without notice.

574-795

Rev. A

This document describes the installation and operation of the Simplex 4190-9011/
9012 Fiber Optic Audio Repeater.  The 4190-9011 Master Unit and the 4190-
9012 Slave Unit are option modules that mount within a 4100 or 4120 Fire Alarm
Control Panel (FACP).

The Simplex Fiber Optic Audio Repeater is designed to “drop-and-repeat” one,
unidirectional, line-level, 600-ohm audio signal. The audio repeater uses either
62.5/125 µ or 50/125 µ fiber optic cables (for distance limitations reference
Table 4).  The Fiber Optic Audio Repeater can be utilized in one-way drop-and-
repeat or self-healing ring systems.

The following is a list of additional documentation that may aid you in the
installation of the 4190-9011/9012 Fiber Optic Audio Repeater.

 

4120/UT System Card Installation Instructions  .......................  574-164

 

4100 Field Wiring Diagram  .....................................................  841-731

 

4100/4120 Interconnect Diagram .............................................  841-869

 

 

The following topics are covered in this publication.

 

 Topic

 See Page #

 Cautions and Warnings

 2

 Specifications

 3

 Fiber Optic Connection

 5

 Installing the Hardware

 6

 Internal Wiring Connections

 7

 Troubleshooting

 10

 
 
 

 

Overview

Related Documentation

 In This Publication

firealarmresources.com

Summary of Contents for 4190-9011











Reviews: