background image

4190-9006 

Remote CRT/Keyboard 

Installation Instructions 

 

 2000 Simplex Time Recorder Co., Westminster, MA 01441-0001 USA 

All specifications and other information shown were current as of publication, and are subject to change without notice. 

 

 

574-830 

Rev. B 

 

DO NOT INSTALL ANY SIMPLEX PRODUCT THAT APPEARS 
DAMAGED.
 

 Upon unpacking your Simplex product, inspect the contents of the 

carton for shipping damage.  If damage is apparent, immediately file a claim 
with the carrier and notify Simplex.  

 

ELECTRICAL HAZARD - 

Disconnect electrical power when making any 

internal adjustments or repairs.  Servicing should be performed by qualified 
Simplex Representatives. 
 

STATIC HAZARD -

 Static electricity can damage components.  Therefore, 

handle as follows: 
1.   Ground yourself before opening or installing components (use the 553-484 

Static Control Kit). 

2.   Keep uninstalled component wrapped in anti-static material at all times.

 

 

The 4190-9006 Remote CRT/Keyboard provides a remote visual indication of 
system events for the 2120 Multiplex System, 4010/4020 Fire Alarm Control 
Panel (FACPs), and 4100+/4120 Fire Alarm System.  The terminal also provides 
for remote communication with each system’s CPU. 

 

The following topics are covered in this publication: 

 

Topic Page 

Number 

Connections 2 

Cable Terminations 

2120 Remote Terminal Connections 

Terminal Configurations 

Programming the 2120 Function Keys 

4010 Front Panel Programming for an RS-232 Port 

10 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Cautions and Warnings

 

Overview 

In This Publication 

 

 

firealarmresources.com

Summary of Contents for 4190-9006













Reviews: