Simex SRP-147, User Manual

Page: 54 / 64

User manual - METER SRP-147
Register Write Range Register description
49h Yes -999 ÷ 999 “ HySt ” parameter in “ rEL4 ” menu, no decimal point included
4Ah Yes 0 ÷ 5
“
modE
” parameter in “
rEL4
” menu:
0 - “ noAC ” mode; 1 - “ on ” mode; 2 - “ oFF ” mode; 3 - “ in ” mode;
4 - “ out ” mode; 5 - “ modb ” mode
4Bh Yes 0 ÷ 999
“t on” parameter in “rEL4” menu, expressed in tenth of seconds or
tenth of minutes depend on “unit” parameter - register no. 4Dh)
4Ch Yes 0 ÷ 999
“toFF” parameter in “rEL4” menu, expressed in tenth of seconds
or tenth of minutes depend on “unit” parameter - register no. 4Dh)
4Dh Yes 0 ÷ 1
“unit” parameter in “rEL4” menu:
0 - seconds; 1 - minutes
4Eh Yes 0 ÷ 2 “AL” parameter in “rEL4” menu: 0 - no changes; 1 - on; 2 - off
4Fh Yes -999 ÷ 9999 “ SEt2
” parameter in “
rEL4
” menu, no decimal point included
50h Yes 0 ÷ 1
“ modE ” parameter in “ HOLd ” menu (type of detected changes):
0 - peaks; 1 - drops
51h Yes 0 ÷ 9999
“ PEA ” parameter in “ HOLd ” menu (minimum detectable change, no
decimal point included)
52h Yes 0 ÷ 199
“ timE ” parameter in “ HOLd ” menu, maximum peaks' (or drops')
display time expressed in seconds
53h Yes 0 ÷ 1
“ HdiS ” parameter in “ HOLd ” menu:
0 - “ rEAL ” mode ; 1 - “ HOLd ” mode
54h Yes 0 ÷ 1
“ H r1 ” parameter in “ HOLd ” menu :
0 - “ rEAL ” mode ; 1 - “ HOLd ” mode
55h Yes 0 ÷ 1
“ H r2 ” parameter in “ HOLd ” menu:
0 - “ rEAL ” mode ; 1 - “ HOLd ” mode
56h Yes 0 ÷ 1
“ H r3 ” parameter in “ HOLd ” menu:
0 - “ rEAL ” mode ; 1 - “ HOLd ” mode
57h Yes 0 ÷ 1
“ H r4 ” parameter in “ HOLd ” menu:
0
- “
rEAL
” mode ;
1
- “
HOLd
” mode
58h Yes 0 ÷ 1
“ HOUt ” parameter in “ HOLd ” menu:
0 - “ rEAL ” mode ; 1 - “ HOLd ” mode
70h 5 Yes -999 ÷ 1999
The value of „ X ” coordinate of point no. 1 of the user defined
characteristic, expressed in 0.1%
71h
5
Yes -999 ÷ 9999
The value of „ Y ” coordinate of point no. 1 of the user defined
characteristic, no decimal point included
72h 5 ÷ 95h 5
Further pairs of „ X ” - „ Y ” coordinates of points no. 2 ÷ 19 of the
user defined characteristic
96h 5 Yes -999 ÷ 1999
The value of „ X ” coordinate of point no. 20 of the user defined
characteristic, expressed in 0.1%
97h 5 Yes -999 ÷ 9999
The value of „
Y
” coordinate of point
no. 20
of the user defined
characteristic, no decimal point included
54