background image

85

ES

PT

ENG

For  the 

30  BF

boiler  to  function  with  LPG,

press 

until 

04 

appears

.

Confirm this value using  

or 

.

Exit the parameters section by pressing

.  

The  table  below  gives  the  values  to  set
when the supply gas is changed:

4.2.2 Adjusting valve pressure (fig. 20)

Set  maximum  and  minimum  pressure  on
gas valves as follows (fig. 20):

– Connect the column or a manometer to

the intake downstream of the gas valve.

In  “25-30  BF”  models,  disconnect  the
valve VENT pressure test point tube (5
fig. 18).

– Remove the cap (1) from the modulator.

– Press the keys (

and 

) at the same

time  for  a  few  seconds  and  completely
open the hot sanitary water faucet.

– Press the key 

(Hi).

– Remember  that  rotating  clockwise  will

increase  pressure  while  rotating  anti-
clockwise will diminish it. 

– Adjust maximum pressure using the nut

(3) with a wrench to the maximum pres-
sure value indicated in 

Table 4

– Adjust  the  maximum  pressure  before

adjusting the minimum.

– Press the key

(Lo) while the sanitary

water tap is on, with the water running.

– Lock  the  nut  (3)  in  place,  turn  the

screw/nut  (2)    to  the  minimum  pressu-
re indicated in 

Table 4

– Press  the  keys (

and 

)  while  kee-

ping  the  hot  sanitary  water  running  all
the  time,  and  check  that  the  maximum
and  minimum  pressures  correspond  to
the  set  values;  if  necessary  correct  the
regulation.

– Press the key 

again to quit the func-

tion.

– Put  the  pipe  back  on  the  valve  VENT

pressure test point.

– Remove  the  manometer,  remembering

to tighten the screw for closing the pres-
sure test point.

– Put the plastic cap (1) back on the modu-

lator  and  seal  with  a  drop  of  coloured
sealant if necessary.

BOILER

GAS 

MODELS

PAR 1

METHANE

25

01

BF

(G20)

30

02

LPG

25

03

(G30/G31)

30

04

METHANE

25

05

OF

(G20)

30

06

LPG

25

07

(G30/G31)

30

08

3

2

1

Fig. 20

KEY
1 Plastic tap
2 Minimum pressure adjusting nut
3 Maximum pressure adjusting nut

Summary of Contents for FORMAT DGT 25 BF
































Reviews: