background image

10

IQ Power Wireless Link

5201319 Rev B

Connect IQ Power and IQ Easy Devices

:  IQ Power devices connect to available 

RJ-45 sockets, 1 through 4 on the Hub.  IQ Easy devices connect to available M12 

Connectors DEV1 through DEV 4 on the Hub.
The IQ Power Hub with Bluetooth Adapter is an extension of the Control Station.  

As such, connection procedures, limitations, and device addressing should be carried 

out as described in the IQ Power Control Station instruction manual and in the 

Addressing section above.

Verify System Communications

Once all previous steps have been performed, devices can be wired and powered up 

one at a time. Communication to the Control Station will need to be verified. To 

verify communication, observe the home screen of the Control Station. If the device 

communicates properly, the device should have an icon on the home screen. If the 

device does not show up, follow the troubleshooting guide in this manual, or the 

manual provided with the missing device. Repeat until all devices are connected and 

communicating.

5. OPERATION 

The Hub provides power and communication to all IQ Power and IQ Easy devices 

connected to it and to the Bluetooth Adapter.  The Hub has a green POWER LED 

which should be lit during operation.
The Bluetooth Adapter provides wireless communication between connected devices 

and the Control Station.
Before using the devices with the Bluetooth Adapter, each device must be given an 

address by connecting it directly to the control station. 
1.  Plug the device to be addressed into the Control Station.
2.  Once the device icon has appeared on the Control Station home screen, select 

the device to open up the device page.

3.  Tap on the page arrow until the screen with the device address setting appears.
4.  Tap on the pencil next to the address setting to change the address. The 

password screen will appear. Type in the password given to the Control Station, 

then tap on the address number (1-10) to be assigned to the device connected 

to the Control Station.

5.  Once the address has been assigned, unplug the device from the Control 

Station.

6.  Repeat the process for each device being connected to the Control Station.

NOTE

 – Only 10 device address can be assigned to a Control Station. If 

more devices are required, an additional Control Station will be needed.

Summary of Contents for IQ Power

















Reviews: