manualshive.com logo in svg

SILENT KNIGHT SK-2224, Installation And Operation Manual

Share
Download
SILENT KNIGHT SK-2224 Installation And Operation Manual Download Page 13

Model SK-2224 Fire Alarm Control Panel Installation/Operation Manual

3-6

151165

3.7

Assembly

The components listed in Table 3-1 are all packed within the cabinet and require some 
assembly. Follow these steps to assemble the components inside the cabinet:

1. Remove keys from the envelope taped to the top of the cabinet.

2. Unlock the cabinet door.

3. Remove the packing material and the SK-2224 components.

4. Snap the bezel into the opening in the front of the cabinet. See Figure 3-3.

Note: The bezel will fit in only one way.

Figure 3-3  The SK-2224 Assembly Diagram

5. With the two #8 screws and the two #8 nuts (with built in washers), mount the transformer 

in the holes in the upper left hand corner of the cabinet. See Figure 3-3.

6. With the three self-tapping screws mount the control board on the cabinet stand-offs.

Note: See Section 4 for transformer connections and battery connections.

Important!

The electronic components on the control panel are sensitive to electrostatic discharge 
(static electricity). Wear a grounding strap when handling the control board.

Side View of
Slotted Stand-Off

Bezel Insertion

Transformer
Installation

CPU Mounting
Screws

Summary of Contents for SK-2224































































Reviews:

No comments

Brands by name

Popular brands

Load more brands