SIIG US2265 User Manual Download Page 7

Page: 7 / 48

User's Manual

The purpose of this manual is to introduce you to your

USB 2.0+1394+UltraATA RAID

. It will guide you on how to

install the card and software for proper operation in your

computer. Please save this manual for future reference in the

event you wish to connect other devices to your system.

This manual is comprised of the following sections:

Chapter 1:

Introduction

Provides unpacking instructions, and

introduces features and specifications of this

board.

Chapter 2:

RAID

General overview of RAID with instructions

on how to configure your RAID arrays.

Chapter 3:

Installation

Describes how to install the card, drivers and

utilities to your system.

Chapter 4:

Using Utilities

Describes how to use the CMD Medley GUI

in Windows.

Chapter 5:

Technical Support and Product Return

Provides instructions on how to obtain

technical support or return a product in the

event of a problem.

About This Manual

Summary of Contents for US2265

















































Search results

Summary of Contents for US2265

Reviews:

Related manuals for US2265

Brands by name

Popular brands

SIIG US2265, User Manual

Search results

Summary of Contents for US2265

Reviews:

Related manuals for US2265

Brands by name

Popular brands