background image

3

These operating instructions are intended to
simplify familiarization with the strapping tool and
the possibilities of application for the intended
purpose.  The operating instructions contain
important information concerning the safe,
proper and efficient use of the strapping tool. 
Observation of the information will help to avoid
danger, reduce repairs and stoppages and
increase the reliability and service life of the
strapping tool.

The operating instructions must always be
available at the place of operation of the
strapping tool.  They must be read and observed
by all persons concerned with work on the
strapping tool.  This work specificity includes
operation, refilling of operating material, fault
elimination and maintenance

In addition to the operating instructions and the
regulations for accident prevention effective in
the country of use and place of application, the
recognized technical regulations for safety and
proper working must also be observed.

CAUTION!

Used where there is
danger to life and health.

WARNING!

Used for danger which
can cause material
damage.

NOTE!

Used for general
information and
information which if not
followed can cause faults
in the operating
sequence.

This tool is manufactured without any physical or
chemical substances which could be dangerous
to health.  For disposal of all the parts, the
governmental instructions must be observed.

Dealers offer an 
environmentally
friendly battery
disposal service

Do not open the battery.

Do not throw the used
battery into household
waste, fire or water.

Defective or used
batteries undergo a
complete recycling
process.

 2

GENERAL INFORMATION

2.1 INFORMATION ON

ENVIRONMENTAL PROTECTION

Summary of Contents for BHC

















Reviews: