SignalFire Sentinel-yTherm Series Interface Manual Download Page 2

Page: 2 / 13

SignalFire Telemetry

Rev 1.6

Specifications

Enclosure Size

3.5”

tall ×

5.0” wide

5.0” deep

Power Source

Internal IS Lithium battery pack

SignalFire Part Number: 3BIS

External Solar battery system

SignalFire Part Number: Sentinel-HCSolar

DC-DC Converter

SignalFire Part Number: DCDC-Sentinel

Other external power supply meeting the power entity parameters from the
control drawing.

Temperature Rating

-40°C to +60°C

Radio Frequency

902-928MHz Ism Band, FHSS radio, internal antenna

Compliance

Certified for use in Class I, Division 1 groups C and D. EXi [EXi] FCC/IC Certified.

WARNING: Use of this equipment in a manner not specified by the manufacturer may
impair the protection provided by the equipment.

WARNING: The use of any parts not supplied by the manufacturer violates the safety rating
of the equipment.

The associated apparatus provides intrinsically safe outputs.

L’appareil associ

é fournit des sorties à sécurité intrinsèque.

Refer to control drawing

“Sentinel –

Control Drawing

–

Modbus, Thermocouple, RTD, and Float Stick”

for

requirements when used in a Class I Division 1 area.

Summary of Contents for Sentinel-yTherm Series














Search results

Summary of Contents for Sentinel-yTherm Series

Reviews:

Related manuals for Sentinel-yTherm Series

Brands by name

Popular brands

SignalFire Sentinel-yTherm Series, Interface Manual

Search results

Summary of Contents for Sentinel-yTherm Series

Reviews:

Related manuals for Sentinel-yTherm Series

Brands by name

Popular brands