SIGMATEK HZS 7321 Technical Manual Download Page 33

Page: 33 / 52

TOUCH OPERATING PANEL

HZS 7321

04.09.2020

Page 31

12 Status and Error Messages

Status and error messages are displayed in the LASAL CLASS software status test.
POINTER or CHKSUM messages are shown on the terminal screen.

Number

Message

Definition

Cause/solution

RUN RAM

The user program is currently running in
RAM.

The display is not affected.

Info

RUN ROM

The user program stored in the program
memory module was loaded into the RAM
and is currently running.

The display is not affected.

Info

RUNTIME

The total time for all cyclic objects ex-
ceeds the maximum time; the time can
be configured using 2 system variables:

Runtime: Remaining time

SWRuntime: Preset value for runtime
counter

Solution:

Optimize the application's cy-

clic task.

Use higher capacity CPU.

Configure preset value

POINTER

Incorrect program pointers were de-
tected before running the user program

Possible Causes:

The program memory module

is missing, not programmed or
defective.

The program in the user pro-

gram memory (RAM) is not ex-
ecutable.

The buffer battery has failed.

The user program has overwrit-

ten a software error.

Solution:

Reprogram the memory mod-

ule, if the error reoccurs ex-
change the module.

Exchange the buffering battery

Correct programming error

CHKSUM

An invalid checksum was detected before
running the user program.

Cause/solution: s. POINTER

Summary of Contents for HZS 7321





















































Search results

Summary of Contents for HZS 7321

Reviews:

Related manuals for HZS 7321

Brands by name

Popular brands

SIGMATEK HZS 7321, Technical Manual

Search results

Summary of Contents for HZS 7321

Reviews:

Related manuals for HZS 7321

Brands by name

Popular brands