SIGMATEK HZS 7321 Technical Manual Download Page 6

Page: 6 / 52

HZS 7321

TOUCH OPERATING PANEL

Page 4

04.09.2020

Process Diagram ...................................................................30

Status and Error Messages ...................................................31

Transport/Storage ..................................................................39

Storage ...................................................................................40

Maintenance ...........................................................................41

15.1

Cleaning and Disinfecting the Touchscreen ............................ 41

15.2

Service ......................................................................................... 42

15.2.1

Calibrating the Touch Screen ............................................................ 42

15.3

Repair ........................................................................................... 42

Buffer Battery .........................................................................43

16.1

Exchanging the Battery: 1. Option ............................................ 44

16.2

Exchanging the Battery: 2. Option ............................................ 45

Application Information .........................................................47

18.1

Interface Assignment ................................................................. 47

18.2

Configuration .............................................................................. 47

Disposal ..................................................................................48

Introduction

1.1

Target Group/Purpose of this Operating Manual

This operating manual contains all information required to operate this product.

This operating manual is intended for:

Summary of Contents for HZS 7321





















































Search results

Summary of Contents for HZS 7321

Reviews:

Related manuals for HZS 7321

Brands by name

Popular brands

SIGMATEK HZS 7321, Technical Manual

Search results

Summary of Contents for HZS 7321

Reviews:

Related manuals for HZS 7321

Brands by name

Popular brands