Sigfox WSSFCB-NH3 User Manual Download Page 18 | Manualshive

Page: 18 / 36

background image

Signal received « ALERT 2 »:

Insert the batteries into Sigfox NH3-BLE device, wait 1 minute for configuration stage end, then Sigfox NH3-BLE will

broadcast BLE data.

Then insert the batteries into BLE Indicator, place it near to Sigfox NH3BLE

When BLE Indicator has got ID NOT MATCH with ID from Sigfox NH3-BLE, BLE Indicator will beep 2 times. So

you need to clear that ID before pairing the BLE Indicator with the new Sigfox device. To clear the ID in BLE

Indicator, place magnet key to reed switch area (marked as a magnet on the nameplate), the BLE indicator will

beep 1 time, and the status led (the led on side of the board) blink WHITE.

5.5 Pairing with BLE Indicator

It is recommended that when adding an ID to a BLE Indicator you should clear the ID first.

«
...
16
17
18
19
20
...
»

Summary of Contents for WSSFCB-NH3





































Reviews:

No comments

Related manuals for WSSFCB-NH3

Brand: NEC Pages: 5

Brand: Warmup Pages: 4

Brand: 3SIXT Pages: 12

Brand: APOLON Pages: 19

E-Bike Frontlight E 80

Brand: RFR Pages: 2

Brand: PullRite Pages: 10

Brand: Viking Pages: 1

Brand: inventum Pages: 32

Brand: Fuzion Pages: 8

USB temperature

Brand: MADRIX Pages: 2

Brand: Datavideo Pages: 24

Brand: A&D Pages: 10

Brand: 7 A.M. Enfant Pages: 2

StreetLine Series

Brand: SAAS Pages: 4

Around the World Move

Brand: X-lander Pages: 63

Brand: Audi Pages: 4

PROFESSIONAL TRIPOD

Brand: Zhumell Pages: 12

Brand: Ecco Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands