SIG T-Clips EP ARF Assembly Manual Download Page 14

14

WARNING!  THIS IS NOT A TOY!

Flying machines of any form, either model-size or full-size, are not toys!
Because of the speeds that airplanes must achieve in order to fly, they
are capable of causing serious bodily harm and property damage if they
crash.  

IT IS YOUR RESPONSIBILITY AND YOURS ALONE

to assemble

this model airplane correctly according to the plans and instructions, to
ground test the finished model before each flight to make sure it is com-
pletely airworthy, and to always fly your model in a safe location and in a
safe manner.  The first test flights should only be made by an experienced
R/C flyer, familiar with high performance R/C aircraft.

JOIN THE AMA

The governing body for radio-control model airplanes in the United States
is  the  ACADEMY  OF  MODEL  AERONAUTICS,  commonly  called  the
AMA.  The AMA SAFETY CODE provides guidelines for the safe opera-
tion of R/C model airplanes.  While AMA membership is not necessarily
mandatory, it is required by most R/C flying clubs in the U.S. and provides
you with important liability insurance in case your R/C model should ever
cause serious property damage or personal injury to someone else.

ACADEMY OF MODEL AERONAUTICS

5161 East Memorial Drive

Muncie, IN  47302

Telephone:  (765) 287-1256

AMA WEB SITE:  www.modelaircraft.org

CUSTOMER SERVICE

SIG MFG. CO., INC. is committed to your success in both assembling 
and flying the RASCAL 72EG ARF.  Should you encounter any problem
building this kit or discover any missing or damaged parts, please feel
free to contact us by mail or telephone.   

SIG MFG. CO., INC.

P.O. Box 520

401 South Front Street

Montezuma, IA  50171-0520

                               PHONE:  1-641-623-5154

                                     FAX:  1-641-623-3922

SIG WEB SITE:  www.sigmfg.com

SIG E-MAIL:  [email protected]

LIMIT OF LIABILITY

The craftsmanship, attention to detail and actions of the builder/flyer of 
this model airplane kit will ultimately determine the airworthiness, flight 
performance, and safety of the finished model.  SIG MFG. CO.’s obligation
shall be to replace those parts of the kit proven to be defective or missing.
The  user  shall  determine  the  suitability  of  the  product  for  his  or  her 
intended use and shall assume all risk and liability in connection therewith.

THE “T-CLIPS” STORY 

Summary of Contents for T-Clips EP ARF

















Reviews: