.
7.
Place the right fuselage side on the building board and place formers F-6 and F-7 into position. These formers should be 90
degrees to the fuselage side. Glue the formers to the fuselage side.
8.
Glue the left fuselage side into position on the formers. The formers should also be 90 degrees to this fuselage side.
9.
Glue the main landing gear support F-6 into position with the markings "TF" at the front and facing the inside of the
fuselage. Glue former F-5 into position.
10.
Glue parts F-9A to part F-9 as shown on the plan.
11.
Gently squeeze the aft end of the fuselage sides together and hold with two clothes pins. Place the formers F-9 and F-10
into position and glue them to the fuselage sides. Glue the aft end of the fuselage sides together making sure that the joint
is straight and not leaning to the left or right.
12.
Place part F-11 into position and glue it to the center of formers F-7, F-9 and F-10. Working from the front to the rear, gently
pinch the fuselage sides into contact with F-11 and glue together.
13.
Place part F-12 into position and glue it to the center of formers F-7, F-9 and F-10.
14.
Working from the front to the rear, gently pinch the fuselage sides into contact with F-12 and glue together.
15.
Fit part F-13 to the fuselage and glue into position.
16.
Fit part F-14 to the fuselage and glue into position.
17.
Glue parts F-15 (L&R) into position on the inside of the fuselage sides at the nose of the model.
18.
Glue part F-16A to the bottom rear of F-16 to make the removable hatch.
19.
Cut a piece of 1/4" sq. spruce 1" long and glue to the rear face of F-5. The top of the spruce should be 3/32" below the top
edge of F-5. Now fit the hatch into position and drill a 1/32" hole in the forward end for the hatch hold down screw.
Building the Left Wing
20.
Pin the lower 1/4" sq. spar and the lower trailing edge sheet to the left wing plan.
21.
Glue the lower plywood dihedral braces to the front and rear of the lower spar. Cut the lower 1/16" sheet for the lower
inboard end of the wing and glue in place between the trailing edge and the dihedral brace.
22.
Place the first W-1 rib into position. Use the dihedral gauge to angle the top of this rib toward the tip and glue the rib into
position.
23.
Glue the second W-1 rib and all of the W-2 ribs into position. These ribs should be 90 degrees to the building board.
24.
Glue the top 1/4" sq. spar into position. The inboard end of the spar should end flush with the face of the W-1 rib. Glue the
top plywood dihedral braces to the front and rear of the top spar.
25.
Glue the 1/4" sq. leading edge, the 3/32" sq. strips and the top trailing edge sheet to the wing.
26.
Add the 1/16" sheet to the inboard end of the wing between the spar and the trailing edge. Use three pieces 1/16" sheet to
sheet the inboard top of the wing from the spar to the leading edge. These pieces go between the 3/32" sq. strips and not
on top of them.
27.
Remove the wing from the plan and add the lower 1/16" sheet to the inboard end between the spar and the leading edge.
28.
Trim and sand the spars, leading edge and the trailing edge flush with the last W-2 rib.
