background image

Instruction

Read these instructions carefully before use.
Please keep these instruction after assembling.

Beaver DHC 2 V2

Ord. No.

00 6135

GB

!

Safety precautions

This radio control model is not a toy!

Not suitable for persons under 14 years!

* First-time builders should seek advice people having 
  building experience in order to assemble the model
  correctly and to produce its performance to full extent.
*  Assemble this kit only in places out of children’s reach!
*  Take enough safety precautions prior to operating this
  model. You are responsible for this model’s assembly and
  safe operation!
* Always keep this instruction manual ready at hand for
  quick reference, even after completing the assembly.

Safety precautions

This radio control model is not a toy!

Not suitable for persons under 14 years!

* First-time builders should seek advice people having 
  building experience in order to assemble the model
  correctly and to produce its performance to full extent.
*  Assemble this kit only in places out of children’s reach!
*  Take enough safety precautions prior to operating this
  model. You are responsible for this model’s assembly and
  safe operation!
* Always keep this instruction manual ready at hand for
  quick reference, even after completing the assembly.

Summary of Contents for Beaver DHC 2 V2

























Reviews: