manualshive.com logo in svg

SIG SIGRC80 Rascal C, Instruction Book, Page: 11 / 31

Share
Download
SIG SIGRC80 Rascal C Instruction Book Download Page 11

. 

26. As shown on the plans, the center section of the wing is integrated into the 

fuselage structure. In the following steps, the center section will be built to fit 
perfectly to the fuselage. Later, when building the wing panels, having the center 
already built will be very convenient.

 

 
Start by locating the required laser-cut parts - 1/16" ply W-8 and the Dihedral 
Brace, the 1/8" lite ply wing bolt mounting plate and balsa parts W-1 ribs (2), W-9 
and the four top and bottom laser-cut sheeting pieces. You also need the two 5/32" 
dia. x1-1/4" wing dowels, the 5/16" dia. x1/2" dowel with the drilled center hole, the 
8-32 x1" nylon wing bolt and the shaped fuselage/wing block.

 
27.

 
The top and bottom sheet parts are first glued together, making two complete 
pieces of sheeting - note that these are laser keyed to fit each other at the join line 
and that there is a laser-cut 5/16" dia. hole at the rear edge of both sheeting 
pieces. After gluing the sheets together, lightly sand the joints smooth. Test-fit the 
1/8" lite ply wing bolt plate in place beneath the top wing saddle longerons, against 
the front of F-6. The fit should be good but use a sanding block if needed to make 
it fit perfectly. Glue the bolt plate in place in the fuselage.

 
28.

 
Insert the two 5/32" dia. forward wing dowels into the front of F-4, leaving about 
1/8" of each exposed at the rear. Press ply former W-8 in place over the dowel 
ends, flat to the back face of F-4. Place one of the sheeting pieces in place on the 
top of the fuselage, with the lasered hole to the rear. Hold the sheeting firmly in 
place to W-8 and look at the hole at the rear of the sheet. It should be centered 
over the hole in the wing bolt mounting plate. If the hole in the sheet is too far back, 
trim the front of the sheet a little to move the hole forward. Use a little piece of 
waxed paper directly beneath W-8 to keep glue away from the fuselage. With the 
bottom sheet exactly in place over the top of the fuselage, glue the forward edge of 
the sheet to the bottom edge of W-8. Use a piece of tape at the rear to hold the 
sheet firmly in place.

 

 
29.

 
Lay the fuselage on its right side, on a flat surface. Glue the right W-1 rib in place 
to the back face of W-8 and onto the right edge of the center section sheet. Turn 
the fuselage over and glue the left W-1 in place. Use your sanding block to lightly 
sand each W-1 rib flush with the fuselage sides.

 

 
30.

 
With the center section structure still on the fuselage, glue 1/16" ply dihedral brace 
in place at the front of the 1/8" slots in the W-1 ribs and onto the bottom sheeting. 
Glue the W-9 backup former in place directly behind dihedral brace.

 
Remove the two dowels from the 
fuselage and center section. Use your 
sanding block to chamfer the trailing 
edge bottom sheeting to receive the top 
sheeting. Insert the two 5/32"x1-1/4" wing 
dowels all the way through W-8 and into 
the holes in the dihedral brace. Glue the 
dowels in place.

 

 

 
Mount the center section assembly to the fuselage, with a piece of wax paper beneath the trailing edge. Glue the top 
sheeting in place on the center section - align carefully, wiping off any excess glue.

Summary of Contents for SIGRC80 Rascal C
































Reviews:

No comments