background image

 

WARNING! THIS IS NOT A TOY!

Flying machines of any form, either model-size or full-size, are not toys! Because of the speeds that airplanes must achieve in 
order to fly, they are capable of causing serious bodily harm and property damage if they crash. 
IT IS YOUR RESPONSIBILITY AND YOURS ALONE to assemble this model airplane correctly according to the plans and 
instructions, to ground test the finished model be fore each flight to make sure it is completely airworthy, and to always fly 
your model in a safe location and in a safe manner. The first test flights should only be made by an experienced R/C flyer, 
familiar with high performance R/C aircraft. 
 
The governing body for radio-control model airplanes in the United States is the ACADEMY OF MODEL AERONAUTICS, 
commonly called the AMA. The AMA SAFETY CODE provides guidelines for the safe operation of R/C model airplanes. While 
AMA membership is not necessarily mandatory, it is required by most R/C flying clubs in the U.S. and provides you with 
important liability insurance in case your R/C model should ever cause serious property damage or personal injury to 
someone else. For more information, contact:

ACADEMY OF MODEL AERONAUTICS 

5151 East Memorial Drive 

Muncie, IN 47302 

Telephone: (317) 287-1256

 
 
 

Customer Service

 
SIG MFG. CO. is totally committed to your success in both building and flying the SEALANE design. Should you encounter any 
problem building this kit, or discover any missing or damaged parts, please feel free to contact us by mail or telephone.
 
 

 
 
 
 
 
 
 
 

SIG MFG. CO., INC. 
401-7 South Front Street 
Montezuma, IA 50171-0520

SIG MODELER S ORDERLINE: (to order parts)

1-800-247-5008

SIG MODELER S HOTLINE (for technical support)

1-641-623-0215

SIG WEB SITE

www.sigmfg.com

© Copyright SIG Mfg. Co., Inc.

 

SIG MFG. CO., INC............Montezuma, Iowa 50171-0520

 

LIMIT OF LIABILITY:

 The craftsmanship, attention to detail and actions of the builder/flyer of this model airplane kit will 

ultimately determine the airworthiness, flight performance and safety of the finished model. SIG MFG. CO's obligation shall be 
to replace those parts of the kit proven to be defective or missing. The user shall determine the suitability of the product for his 
or her intended use and shall assume all risk and liability in connection therewith.

Summary of Contents for Sealane



























Reviews: