Sifos Technologies PhyView PVA-3000 Reference Manual Download Page 44

Page: 44 / 134

PVA-3000 Reference Manual

December 2, 2019

Sifos Technologies

Page
44

3.6.1.

Port Config Menu-Wide Controls

The

Read Settings

button is the only

menu-wide operation in the

Port Config

menu.

Read Settings

is used to update

all

Port Config

menu configuration

settings to match actual resource settings
in the current test port of the currently
connected instrument. Generally, this
operation is not frequently necessary
because each time a new test port is
selected in the Slot-Port helper menu or
each time the

Port Config

tab menu is

selected, all displayed settings will
update automatically to match actual
resource settings in the test port.

The

Read Settings

button will also clear

out any pending configuration changes
and assure synchronization of the Port
Config tab menu to associated test port
resources.

3.6.2.

Port Config Actions Sub-Menu

The

Actions

sub-menu within the

Port Config

tab menu (

see Figure 3.10

) is used to:

Apply Port Connection configuration changes

Apply Port Impairments configuration changes

Copy Port Connection, Port Impairment, and/or Active Impairment configuration settings to other test ports from
the current test port

Whenever radio buttons are selected in the

Port Connection

and

Port Impairments

frames of the Port Config menu, the

Apply Selected Port Settings

button will

annunciate

red

to indicate that a pending change should be applied (

see Figure 3.11

At this point, pressing the

Apply Selected Port Settings

button will effect the

selected configuration setting in the current test port if the corresponding checkbox for

Port Connections

and Port Impairments

is also selected.

The three checkboxes,

Port Connections

Port Impairments

, and

Active

Impairments

serve as filters for which settings can be applied or replicated to other

test ports. For example, if

Port Connections

is de-selected, then any settings selected

under the Port Connection frame will not be applied when the

Apply Selected Port

Settings

button is pressed and will not be copied when the

Copy Selected Settings

button is pressed.

Replications of configuration settings will be
further discussed below in Section 3.7.

3.6.3.

Port Connection Sub-Menu

The

Port Connection

sub-menu governs the switch position of the PVA Switch

in Figure 2.1.

Test PHY

causes the

TEST

interface to connect to the TEST

PHY while

THRU Port

routes the

TEST

interface via the 4-pair coupler to the

THRU

interface. When either of these radio buttons are selected, the

Apply

Selected Port Settings

button in the

Actions

frame will annunciate

red

(

see

Figure 3.11

) meaning that the configuration change will only take effect when

that button is pressed

and

if the

Port Connections

checkbox is selected.

3.6.4.

Port Impairments Sub-Menu

The

Port Impairments

sub-menu also controls test port switching options. The

100 Meter Cat5e

sub-menu represents the

Line Loss

impairment discussed

Figure 3.10

Actions Sub-Menu

Figure 3.11

Pending Port Config

Figure 3.9

Port Configurations Tab Menu

Summary of Contents for PhyView PVA-3000







































































































































Search results

Summary of Contents for PhyView PVA-3000

Reviews:

Related manuals for PhyView PVA-3000

Brands by name

Popular brands

Sifos Technologies PhyView PVA-3000, Reference Manual

Search results

Summary of Contents for PhyView PVA-3000

Reviews:

Related manuals for PhyView PVA-3000

Brands by name

Popular brands