SIFANG CSC-161 Product Manual Download Page 28

Page: 28 / 64

Communication

Figure 16 Single channel, communication through dedicated fiber optical cable

IED

Channel A

Channel B

Single-mode FO

Length: <60kM or

60~100kM

Overhead Line or Cable

Figure 17 Double channels, communication through dedicated fiber optical cable

Communication converter

The link between the IED and a

multiplexed communication network is

made

dedicated

communication

converters (CSC186). They have a

fiber-optic interface with 1310 nm and 2 FC

connectors to the protection IED. The

converter can be set to support an

electrical G703-64 kbit/s or G703-E1

2Mbit/s interface, according the require-

-ment of the multiplexed communication

network.

Communication

converter

Communication

converter

Digital

communication

network

G703.5(E1: 2048kbit/s)

G703.1(64kbit/s)

IED

Overhead Line or Cable

Figure 18 Single Channel, communication through digital communication network

Summary of Contents for CSC-161

































































Search results

Summary of Contents for CSC-161

Reviews:

SIFANG CSC-161, Product Manual, Page: 28 / 64

Search results

Summary of Contents for CSC-161

Reviews: