background image

MIN/MAX MIN/MAX

300   A    3mA

0.15 +5

+ 3 % v. M

1)  Reactivated by falling below the specified limits of the measured value .
2) Referring to AC values.
3) When storing a value for the first time twice a sound signal.
For following “holds” only twice if actual hold value differs from first stored value 
by less than 100 digits.
The analog indication is not influenced by the DATA hold. You can still read the 
actual measured value. Note that with a “held” digital display, the location of the 
decimal point is also held.
As  long  as  the  DATA  hold  function  is  active,  manual  range  selection  is  not 
possible.

The  DATA  hold  function  is  switched  off,  when  the  “DATA”  pushbutton  (3)  is 
pressed for approximately 1s, when the function selector switch (6) is operated, 
or  when the meter is turned OFF and ON again.

6. Minimum value and maximum value “MIN/MAX” 

storage facility with time display

With the MIN/MAX function, you can “hold” the minimum and the maximum  
measured value which was applied to the input of the meter after activating  
MIN/MAX.  The  most  important  application  is  the  determination  of  the 
minimum    and  the  maximum  value  for  long-term  monitoring  of  measured 
quantities.
The function “MIN/MAX” can be activated in all ranges except for the diode  
test.  However,  for  frequency  and  capacitance  measurement  the  relative 
time  display is not possible.
MIN/MAX  does  not  influence  the  analog  indication;  you  can  still  read  the 
actual  measured value.
Apply the measured quantity to the meter and select the measuring range 
prior  to activating the MIN/MAX function.
With  the  function  activated,  you  can  only  select  the  measuring  ranges   
manually. However, the stored MIN/MAX values are cleared. 
The MIN/MAX function is switched off, when the MIN/MAX pushbutton (3) is  
pressed  for  approximately  1s,  when  the  function  selector  switch  (6)  is 
operated  or when the meter is turned OFF and ON again.

7.

Voltage measurement

ê

According to the voltage to be measured, set the function selector switch 

(6) to V~, V  ---  or V ---

Summary of Contents for Gamma 10

















Reviews: