Siesta AHQ100AV1 Installation Manual Download Page 8 | Manualshive

Page: 8 / 24

background image

1-6

Install the Suspension Bolts

Install the suspension bolts so that it can support the indoor unit.
Adjust distance to ceiling before installation.
Refer to the dimension given to install the unit.

Install the Indoor Units

Insert the suspension bolts into the

Þ

ttings of the hanger bracket.

Set the nuts and washer on the both side of the metal

Þ

ttings.

Secure it with nuts.
Attach the hanger cover (4 pcs) to the units.

1.
2.
3.

1.
2.
3.
4.

Suspension Bolt

Hanger Cover

Hanger Cover

Suspension Bolt

Hanger Rod

Installation Floor Standing Type

28mm

479mm

547mm or more

Mounting Bracket

509mm

458mm

301mm or more

759mm or more

Rear Piping Hole

Floor

123mm

78mm

40mm

307mm

Installation Ceiling Type

UNDER CEILING INSTALLATION (AHQ71AV1)

«
...
6
7
8
9
10
...
»

Summary of Contents for AHQ100AV1

























Reviews:

No comments

Related manuals for AHQ100AV1

Brand: Panasonic Pages: 53

Brand: Ultravation Pages: 4

Brand: Guzzanti Pages: 140

R410A Split Series

Brand: Dakin Pages: 40

Brand: IQAir Pages: 28

Brand: Prem-I-Air Pages: 15

DOLCECLIMA COMPACT

Brand: Olimpia splendid Pages: 66

Brand: Shinco Pages: 16

Brand: TaoTronics Pages: 15

Ultra Heat GMV Multi VRF Series

Brand: Gree Pages: 64

Brand: HELLER Pages: 9

Platinum Split 4000 Evaporator

Brand: WhisperKool Pages: 50

Brand: GE Pages: 32

Brand: GE Pages: 32

Brand: Johnson Controls Pages: 88

Brand: Beko Pages: 64

Brand: Beko Pages: 52

Brand: Beko Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands