16
Figure
Vacuuming with accessories
A
ttach the nozzles to the suction pipe or handle as
required:
a)
Crevice nozzle for vacuuming crevices and corners,
etc.
b)
Upholstery nozzle for vacuuming upholstered
furniture, curtains, etc.
c)
Hard-floor tool
For vacuuming hard floor coverings
(tiles, parquet flooring, etc.)
●
Push the telescopic tube into the connecting piece of
the hard floor tool until it locks in place.
●
To release the connection, press the locking collar
and pull out the telescopic tube.
Figure
●
After use, place the crevice or upholstery nozzle back
into the accessories compartment in the appliance lid.
Turbo brush
If your appliance is equipped with a turbo brush, please
consult the accompanying instruction manual for
instructions on its use and maintenance.
Figure
●
You can use the nozzle parking aid on the back of the
appliance if you wish to stop vacuuming for a short time.
●
Once you have switched off the appliance, slide the
hook on the floor tool into the recess on the rear of
the appliance.
Figure
To overcome obstacles, e.g. steps, the appliance can
also be carried by the handle on the appliance body.
When you have finished vacuuming
Figure
●
Pull out the mains plug.
●
Briefly pull the power cord and release
(The power cord rewinds automatically).
Figure
●
To store or transport the appliance, you can use the
storage aid on the underside of the appliance.
●
Stand the appliance upright. Slide the catch on the
floor tool into the groove on the underside of the
vacuum cleaner.
Changing the filter
!
Please note: Always switch off the appliance before
changing the filter.
13
14
15
16
17
12*
Replacing the bag
Figure
a)
If the dust bag change indicator lights up red
continuously when the floor tool is lifted from the floor
and the highest power setting has been selected, the
dust bag must be changed, even though it may not yet
be full. Even if the dust bag is not full, it may still need
changing, due to the type of dust which has been
vacuumed.
First check that the nozzle, suction pipe and flexible
hose are not blocked, as this would also lead to the
dust bag change indicator being triggered.
b)
The handle can easily be detached from the hose to
remove blockages.
Figure
Opening the lid
●
Open the lid by moving the locking lever in the
direction of the arrow.
Figure
a)
Seal the dust bag by pulling the sealing tab, and
remove the bag.
b)
Insert the new dust bag fully into the holder.
!
Caution: the lid will only close if a dust bag has been
inserted.
Cleaning the motor protection filter
The motor protection filter should be cleaned regularly
by tapping out the dirt and rinsing.
Figure
●
Open the dust bag compartment lid.
Figure
●
Pull out the motor protection filter in the direction of
the arrow.
●
Clean the motor protection filter by tapping out the dirt.
●
If it is very dirty, the motor protection filter should be
rinsed out.
The filter must then be left to dry for at least 24 hours.
●
After cleaning, insert the motor protection filter into
the appliance and close the dust bag compartment lid.
If required, you can purchase a replacement motor
protection filter through our after-sales service
(see after-sales service centres directory).
Order no. 618907
19
20
21
19
18*
en
Summary of Contents for Z 5.0
