manualshive.com logo in svg

Siemens SIWAREX WL230 BB-S SA, Operating Instructions Manual

Share
Download
Siemens SIWAREX WL230 BB-S SA Operating Instructions Manual Download Page 22

NOTICE
Damage to load cells through incorrect mounting
• Provide indented claws or crane eyebolts on the load bearer to ensure that hoisting gear can 

be used safely.

• Load cells must never be overloaded. Put the load carrier down slowly for this reason. 

With load cells of smaller rated loads in particular, there is a risk of stretching the load cell 
bodies when attaching force transfer devices, e.g. when tightening locknuts.

• Adjust the existing overload protection to ensure that it can still reliably sense transfer of the 

required load. The overload protection must permit a rise in weight unhindered until the 
setpoint weight is reached.

• Protect the gap between the load cell and overload protection from the build up of dirt or 

ice.

• The load must be introduced in the measuring direction of the load cell. Torsional and 

bending moments, eccentric loads and lateral forces are disturbances. These disturbances 
falsify the measured result and can damage the load cell if the permissible limits of the load 
cell and mounting components are exceeded.
The mounting components normally allow so much room for movement that heat 
expansion will not result in lateral loading.

• Protect the load cell against higher impact energy levels by using Siemens mounting 

accessories.

NOTICE
Destruction of load cells

Proceed carefully with installation. The load cells can be destroyed if they are installed 
incorrectly.

4.2

Procedure for mounting the device

Procedure for mounting the device 

1. Observe the installation guidelines for the mounting components.

– You can find dimension drawings of installation elements under Dimension drawings 

(Page 73).

– Lay the cables for the load cells through cable glands in the form of a vertical downwards 

loop to discourage the penetration of water.

2. Check that the load cells and mounting components are installed correctly, e.g. by checking 

the mounting dimensions and oscillation distances.

See also

Nameplate layout (Page 19)

Installing
4.2 Procedure for mounting the device

SIWAREX WL200

22

Operating Instructions, 12/2021, A5E02199611B-13

Summary of Contents for SIWAREX WL230 BB-S SA



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands