manualshive.com logo in svg

Siemens SIWAREX WL230 BB-S SA, Operating Instructions Manual

Share
Download
Siemens SIWAREX WL230 BB-S SA Operating Instructions Manual Download Page 15

Note

The use of multiple entity-Approved/Certified associated apparatus / barriers which have not 
been

Approved/Certified in combination with one another is restricted to the following conditions:
• The associated apparatus /barriers shall all have DC outputs of the same polarity.
• The associated apparatus /barriers shall have an open-circuit voltage (Voc, Vt or Uo) not 

exceeding Ui.

• The sum of the output current (Isc, It or Io) of all of the associated apparatus/barriers shall not 

exceed Ii.

• The sum of the available power (Po) of all of the associated apparatus / barriers shall not 

exceed Pi.

• Ci (incl. load cell cable) + C of additional cable (total) shall not exceed the lowest Ca or Co for 

the associated apparatus / barriers.

• Li (incl. load cell cable) + L of additional cable (total) shall not exceed the lowest La or Lo for 

the associated apparatus / barriers.

• The outputs of all associated apparatus/barriers shall be linear. If necessary, contact barrier 

manufacturer for confirmation of linearity.

See chapter Energy limitation parameters (Page 70).

Safety instructions

2.6 Specific conditions of use

SIWAREX WL200
Operating Instructions, 12/2021, A5E02199611B-13

15

Summary of Contents for SIWAREX WL230 BB-S SA



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands