background image

Connecting

5

5.1

Basic safety instructions

WARNING

Unsuitable cables, cable glands and / plug-in connectors
Danger of explosion in hazardous areas.
● Only use cable glands/plug-in connectors that fulfill the requirements of the relevant type 

of protection.

● Only use cables that have been designed for an ambient temperature of at least 20 K 

higher.

● Close cable openings for electrical connections that are unused.
● When replacing cable glands, only use ones of the same type.
● After installation check that the cables are seated firmly.

WARNING

Improper power supply
Risk of explosion in hazardous areas as result of incorrect power supply, e.g. using direct 

current instead of alternating current.
● Connect the device in accordance with the specified power supply and signal circuits. The 

relevant specifications can be found in the certificates, in Technical specifications 

(Page 27) or on the nameplate.

5.1.1

Grounding for Ex (explosion protection) devices

WARNING

Lack of equipotential bonding
Danger of explosion through compensating currents or ignition currents through lack of 

equipotential bonding.
● Make sure that equipotential bonding exists for the device.
● The pressure transmitter must be connected to the equipotential bonding system of the 

plant via the metal housing (process connection) or the ground conductor of the plug.

Exception: It may be permissible to omit connection of the equipotential bonding for devices 

with type of protection "Intrinsic safety Ex i".

SITRANS P220

Compact Operating Instructions, 02/2019, A5E03304437-AB

17

Summary of Contents for SITRANS P series





































Reviews: