Siemens SIPROTEC4 6MD63 Protocol Manual Download Page 42

Page: 42 / 66

Standard mapping 2-2

7SJ61...7SJ63, 7SJ65, 6MD63 PROFIBUS-DP – Bus mapping

C53000-L1840-B006-02

3-6

Offset

Designation of the

SIPROTEC objects

Comments

Internal

object no.

5/4

Alarm Sum Event

1 = Alarm summary event ON

160

5/5

Relay PICKUP

1 = Relay PICKUP (summary alarm)

501

5/6

Relay TRIP

1 = Relay GENERAL TRIP command

(summary alarm)

511

5/7

–

3.2.1.6

Automatic recloser status

Offset

Designation of the

SIPROTEC objects

Comments

Internal

object no.

6/0

>CB Ready

1 = Binary input “circuit breaker ready“ is active

2730

6/1

79 OFF

1 = AR is switched OFF

2781

6/2

79 ON

1 = AR is switched ON

2782

6/3

79 Close

1 = AR close command

2851

6/4

79 Successful

1 = AR successfully completed

2862

6/5

79 Lockout

1 = AR definitive TRIP

2863

6/6

TRIP Gnd Fault

1 = AR TRIP ground fault

2869

6/7

TRIP Ph Fault

1 = AR TRIP phase fault

2870

3.2.1.7

Time overcurrent protection

Offset

Designation of the

SIPROTEC objects

Comments

Internal

object no.

7/0

50/51 PH OFF

1 = Time overcurrent phase is OFF

1751

7/1

50N/51N OFF

1 = Time overcurrent ground is OFF

1756

7/2

50(N)/51(N) PU

1 = Time overcurrent PICKUP

1761

7/3

50/51 Ph A PU

1 = Time overcurrent phase A picked up

1762

7/4

50/51 Ph B PU

1 = Time overcurrent phase B picked up

1763

7/5

50/51 Ph C PU

1 = Time overcurrent phase C picked up

1764

7/6

50/51N GND PU

1 = Time overcurrent ground picked up

1765

7/7

50(N)/51(N)TRIP

1 = Time overcurrent TRIP

1791

8/0

50-2 TRIP

1 = 50-2 TRIP

1805

8/1

50-1 TRIP

1 = 50-1 TRIP

1815

8/2

51 picked up

1 = 51 picked up

1820

8/3

51 TRIP

1 = 51 TRIP

1825

8/4

50N-2 TRIP

1 = 50N-2 TRIP

1833

8/5

50N-1 TimeOut

1 = 50N-1 TimeOut

1835

8/6

50N-1 TRIP

1 = 50N-1 TRIP

1836

8/7

51N TRIP

1 = 51N TRIP

1839

Summary of Contents for SIPROTEC4 6MD63



































































Search results

Summary of Contents for SIPROTEC4 6MD63

Reviews:

Related manuals for SIPROTEC4 6MD63

Brands by name

Popular brands

Siemens SIPROTEC4 6MD63, Protocol Manual

Search results

Summary of Contents for SIPROTEC4 6MD63

Reviews:

Related manuals for SIPROTEC4 6MD63

Brands by name

Popular brands