Siemens SIPROTEC4 6MD63 Protocol Manual Download Page 60

Page: 60 / 66

Standard mapping 2-4

7SJ61...7SJ63, 7SJ65, 6MD63 PROFIBUS-DP – Bus mapping

C53000-L1840-B006-02

5-14

5.2.1.5

Sensitive ground fault protection

Offset

Designation of the

SIPROTEC objects

Comments

Internal

object no.

2/2

50Ns-2 TRIP

1 = 50Ns-2 TRIP

1223

2/3

50Ns-1 TRIP

1 = 50Ns-1 TRIP

1226

5.2.1.6

Thermal overload protection

Offset

Designation of the

SIPROTEC objects

Comments

Internal

object no.

2/4

49 Th O/L TRIP

1 = 49 Thermal overload TRIP

1521

2/5

49 O/L <Theta> Alarm

1 = 49 Overload alarm! Near thermal TRIP

1516

5.2.1.7

Directional time overcurrent protection

Offset

Designation of the

SIPROTEC objects

Comments

Internal

object no.

2/6

67-2 TRIP

1 = 67-2 TRIP

2649

2/7

67-1 TRIP

1 = 67-1 TRIP

2665

5.2.1.8 Diagnosis

•

Ref. to chap. 1.5.5 and 1.5.6 for additional notes regarding "Error with a summary alarm" and "Alarm summary
event".

Offset

Designation of the

SIPROTEC objects

Comments

Internal

object no.

3/0

Device OK

1 = Update of the device replica in the SIPROTEC

device completed after initial start or restart

3/1

ProtActive

1 = At least one protection function is active

3/2

Settings Calc.

1 = Setting calculation is running

3/3

Error Sum Alarm

1 = Error with a summary alarm ON

140

3/4

Alarm Sum Event

1 = Alarm summary event ON

160

3/5

Relay PICKUP

1 = Relay PICKUP (summary alarm)

501

3/6

Relay TRIP

1 = Relay GENERAL TRIP command

(summary alarm)

511

3/7

>No Volt

1 = Binary input “No voltage (fuse blown)" is active

–

Summary of Contents for SIPROTEC4 6MD63



































































Search results

Summary of Contents for SIPROTEC4 6MD63

Reviews:

Related manuals for SIPROTEC4 6MD63

Brands by name

Popular brands

Siemens SIPROTEC4 6MD63, Protocol Manual

Search results

Summary of Contents for SIPROTEC4 6MD63

Reviews:

Related manuals for SIPROTEC4 6MD63

Brands by name

Popular brands