Siemens SION 3AE6113-0 Operating Instructions Manual Download | Manualshive

Page: 6 / 60

background image

Transport, storage and packing

6

9229 0020 176 0B

2019-04-02

Transporting with packing

Transport the transport unit to the installation site or storage location
• with a fork lift or
• with sling gear suspended from a crane

- at a spreading angle of approx. 60° or
- with a spreader bar.

After receipt of delivery:

Checking the transport

unit

• Check the transport unit for damage.
• Major damage must be documented photographically.
• Ensure that any damage to the transport unit is confirmed by the transport com-

pany in writing.

Unpacking

Working equipment

Required tools:

- Knife/scissors
- Lifting equipment with lifting gear
- Pliers or lever.

CAUTION

Risk of injury from sharp edges!

Fasteners may break and have sharp edges.

Always use a suitable tool to lever out fasteners.

Note

Do not cut open or damage the carton, since it is designed to be reused and
because of the belt straps located underneath.

Belt straps could be severed on the pallet floor when cutting open the carton.

The vacuum circuit-breaker is attached to the pallet with belt straps. It is not per-
mitted to transport the vacuum circuit-breaker on the pallet without using belt
straps (see Fig. 3 to Fig. 4).

Note

Risk of tipping over due to shift in centre of gravity!

Vacuum circuit-breakers with mounted contact arms may tip onto the contact sys-
tem if not fixed.

Before undoing the belt straps, ensure that the vacuum circuit-breaker is posi-
tioned safely and hook sling gear to the points marked with crane hooks.

«
...
4
5
6
7
8
...
»

Summary of Contents for SION 3AE6113-0





























































Reviews:

No comments

Related manuals for SION 3AE6113-0

Brand: Eaton Pages: 40

ReliaMod RMS212522LRLR

Brand: ABB Pages: 4

Brand: LEGRAND Pages: 2

DL10 Series DL107

Brand: Di-LOG Pages: 12

Brand: Malmbergs Pages: 2

Brand: Eaton Pages: 81

Brand: IDEAL Pages: 54

Power Defense PD3

Brand: Eaton Pages: 9

Brand: Eaton Pages: 2

Power-Break TSUV1

Brand: GE Pages: 2

Brand: GE Pages: 32

Brand: OEZ Pages: 8

Brand: YOKOGAWA Pages: 1

Brand: Schaltbau Pages: 28

Brand: Delixi Pages: 57

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands