Siemens SINUMERIK MCU1720 Equipment Manual Download Page 26

Page: 26 / 102

4.2

Operator control and display elements

4.2.1

Overview of operating and display elements

①

NCK commissioning switch: Rotary switch with 16 positions

②

PLC mode selector: Toggle switch with the settings RUN/STOP/MRES

③

LED display of the NC (RDY, COM, DIAG)

④

LED display of the PLC (RUN, ERR, MT)

⑤

LED display of the HMIs (PC ON/WD, RUN/STOP, ERR, MT and user LEDs L1/L2/L3)

⑥

On/off switch: The on/off switch does not isolate the device from the power supply. Position "ON" when the "_" symbol
is pressed. When delivered, it is in the "OFF" position.

Figure 4-1

Position of operator control and display elements

Description
4.2 Operator control and display elements

MCU 1720

Equipment Manual, 09/2019, A5E47437728B AB

Summary of Contents for SINUMERIK MCU1720







































































































Search results

Summary of Contents for SINUMERIK MCU1720

Reviews:

Related manuals for SINUMERIK MCU1720

Brands by name

Popular brands

Siemens SINUMERIK MCU1720, Equipment Manual

Search results

Summary of Contents for SINUMERIK MCU1720

Reviews:

Related manuals for SINUMERIK MCU1720

Brands by name

Popular brands