manualshive.com logo in svg

Siemens SINAMICS G120 PM240P-2, Installation Manual, Page: 91 / 106

Share
Download
Siemens SINAMICS G120 PM240P-2 Installation Manual Download Page 91

 

Spare parts and accessories 

 

7.2 Optional accessories 

Power Module PM240P-2 
Hardware Installation Manual, 06/2020, A5E37800827C AD 

89

 

7.2.5

 

Output reactor 

Output reactors reduce the voltage stress on the motor windings and the load placed on the 

converter as a result of capacitive recharging currents in the cables.  
When using a output reactor, observe the following restrictions: 

●

 

The output frequency must not exceed 150 Hz. 

●

 

The pulse frequency must not exceed 4 kHz. 

 

 

NOTICE 
Damage to the output reactor by exceeding the maximum pulse frequency 
The maximum permissible pulse frequency when using the output reactor is 4 kHz. The 

output reactor can be damaged if the pulse frequency is exceeded.  

•

 

When using an output reactor, the pulse frequency of the Power Module must not be 

higher than 4 kHz. 

 

 

NOTICE 
Damage to the output reactor if it is not activated during commissioning 
The output reactor may be damaged if it is not activated during commissioning.  

•

 

Activate the output reactor during commissioning via the parameter specified by the 

converter manufacturer. 

•

 

Activate the output reactor during commissioning according to the electric specifications. 

 

Mounting position 

 

Summary of Contents for SINAMICS G120 PM240P-2











































































































Reviews:

No comments