manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 5 / 346

Share
Download
Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 5

 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

3

 

Change history 

Important changes with respect to the manual Edition 07/2010 

 

New functions in firmware V4.4 

In Chapter 

Predefined settings for the converter interfaces 

•

 

Installing Control Unit (Page 44) 

Two- and three-wire control via terminal block 

•

 

Inverter control (Page 185) 

Unit changeover 

•

 

Application-specific functions 
(Page 219) 

Expanded options for controlling DC braking 

•

 

Braking functions of the converter 
(Page 225) 

Automatic restart expanded by a new mode 

•

 

Automatic restart and flying restart 
(Page 237) 

Trace via STARTER 

•

 

Commissioning with STARTER 
(Page 68) 

 

 

Revised descriptions 

In Chapter 

The description of the PM240-2 and PM250-2 Power 

Modules has been removed. It is expected that this Power 

Module will be released with firmware V4.5. 

•

 

Installing Power Module (Page 30) 

•

 

Technical data, Power Modules 
(Page 305) 

Connecting up the terminal strip 

•

 

Installing Control Unit (Page 44) 

•

 

Adapting the terminal strip 
(Page 85) 

USB interface settings for commissioning with STARTER. 

•

 

Commissioning with STARTER 
(Page 68) 

Slave-to-slave communication via PROFIBUS DP 

•

 

Communication via PROFIBUS 
(Page 98) 

•

 

Application examples (Page 323) 

Acyclic communication via PROFIBUS DP (data set 47) 

•

 

Acyclic communication (Page 113) 

•

 

Application examples (Page 323) 

Connection of the converter to CANopen 

•

 

Configuring the fieldbus (Page 97) 

Function overview 

•

 

Functions (Page 183) 

 

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Reviews:

No comments