Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 307

Page: 307 / 346

Technical data

10.2 Technical data, Power Modules

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

305

10.2

Technical data, Power Modules

Permissible converter overload

There are two different power data specifications for the Power Modules: "Low Overload"

(LO) and "High Overload" (HO), depending on the expected load.

RYHUORDGIRUV

%DVHORDGIRUV

3HUPLVVLEOHRYHUORDG

)RUORZRYHUORDG/2XSWRN:

3HUPLVVLEOHRYHUORDG

)RUORZRYHUORDG/2XSWRN:

3HUPLVVLEOHRYHUORDG

)RUKLJKR2XSWRN:

3HUPLVVLEOHRYHUORDG

)RUKLJKR2XSWRN:

%DVHORDGIRUV

RYHUORDGIRUV

%DVHORDGIRUV

%DVHORDG/2

RYHUORDGIRUV

Figure 10-1 Duty cycles, "High Overload" and "Low Overload"

Note
The base load (100% power or current) of "Low Overload" is greater than the base load of

"High Overload".
We recommend the "SIZER" engineering software to select the inverter based on duty

cycles. See Manuals for your inverter (Page 336).

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews:

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 307 / 346

Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews: