manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 70 / 346

Share
Download
Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 70

Commissioning 

 

4.5 Commissioning with STARTER 

 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 

68

 

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

4.5

 

Commissioning with STARTER 

Preconditions 

You require the following to commission the converter using STARTER: 
●

 

A pre-installed drive (motor and converter) 

●

 

A computer with Windows XP, Vista or Windows 7, which is connected to the converter 

via the USB cable and on which STARTER V4.2 or higher has been installed. 
You can find updates for STARTER in the Internet under: Update or download path for 

STARTER (

Commissioning steps 

Commissioning with STARTER is subdivided into the following steps: 
1.

 

Adapting the USB interface (Page 69) 

2.

 

Generating a STARTER project (Page 70) 

3.

 

Go online and perform the basic commissioning (Page 70) 

4.

 

Making additional settings (Page 74) 

STARTER features a project Wizard that guides you step-by-step through the 

commissioning process.  

 

 

Note 
The STARTER screens show general examples. You may therefore find that a screen 

contains more or fewer setting options than are shown in these instructions. A 

commissioning stage may also be shown using a Control Unit other than the one you are 

using. 

 

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Reviews:

No comments