manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 99 / 346

Share
Download
Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 99

 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

97

 

Configuring the fieldbus 

6

 

Before you connect the inverter to the field bus, you should have completed the basic 

commissioning, see Chapter Commissioning (Page 53) 

Fieldbus interfaces of the Control Units 

The Control Units are available in different versions for communication with higher-level 

controls with the subsequently listed fieldbus interfaces: 

 

Fieldbus 

Profile 

Control Unit 

Interface 

PROFIBUS DP 

(Page 98) 

PROFIdrive 

PROFIsafe 

CU230P-2 DP 

SUB D socket 

USS (Page 119) 

- 

CU230P-2 HVAC 

RS485 connector 

Modbus RTU 

(Page 133) 

- 

CU230P-2 HVAC 

RS485 connector 

BACnet MS/TP 

(Page 143) 

- 

CU230P-2 HVAC 

RS485 connector 

CANopen 

(Page 152) 

- 

CU230P-2 CAN 

SUB-D connector 

Data exchange via the fieldbus  

Analog signals 
The converter always scales signals, which are transferred via the fieldbus, to a value of 

4000 hex. The significance of this numerical value depends on the category of the signal that 

you are transferring. 

Signal category 

4000 hex corresponds to the value of the following parameters 

Speeds, frequencies 

p2000 

Voltage 

p2001 

Current 

p2002 

Torque 

p2003 

Power 

p2004 

Angle 

p2005 

Temperature 

p2006 

Acceleration 

p2007 

Control and status words 
Control and status words always comprise two bytes. Depending on the control type, the two 

bytes are differently interpreted as higher or lower significance. An example for transferring 

control and status words with a SIMATIC control is provided in Chapter STEP 7 program 

example for cyclic communication (Page 328). 

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Reviews:

No comments