Siemens SIMOTION P320-4 E Commissioning And Hardware Installation Manual Download

Page: 191 / 222

SRAM

"OK"?

SRAM image

(storage medium)

"OK"?

SRAM backup

(storage medium)

"OK"?

User data

used

Note

Yes

BACKUP

No message box or

alarms

Overall reset

Required

The user data backed up in the SRAM of the SIMOTION P320‑4 is used.

The user data backed up in the SRAM image on the storage medium of the SIMOTION P320‑4 is

used.

The user data backed up in the SRAM backup on the storage medium of the SIMOTION P320‑4 is

used.

11.5.3

After new installation / update of the SIMOTION P Kernel

If a compatible SIMOTION P Kernel is installed on an already commissioned

SIMOTION P320‑4, the user data backed up in the SRAM is retained.
However, the current software version of the SIMOTION PP320-4 must be identical to the

software version with which the backed-up user data of the SRAM was created.
Now SIMOTION P320-4 is immediately ready to run again.

Note
If you do not want the backed up user data to be used again, you will have to recommission

the SIMOTION P320-4.

Note
Restart of SIMOTION P320-4 required
After a new installation or update of the SIMOTION P Kernel, a restart of the SIMOTION P320-4

is generally required.
If the device is not restarted, the new SIMOTION P Kernel is not activated and you continue

to work with the old firmware.

11.5.4

After restoring a backup copy

If a backup copy (storage medium image) of a commissioned SIMOTION P320-4 is reloaded,

the backed-up user data stored in the SRAM of the SIMOTION P320‑4 is used.
Now SIMOTION P320-4 is immediately ready to run again.

Service and maintenance

11.5 Special power-up situations

SIMOTION P320-4 E / P320-4 S

Commissioning and Hardware Installation Manual, 11/2016

191

Summary of Contents for SIMOTION P320-4 E































































































































































































































Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands

Siemens SIMOTION P320-4 E, Commissioning And Hardware Installation Manual

Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands