Siemens SIMOTICS M-1PH818 Operating And Installation Instructions Download | Manualshive

Page: 92 / 314

background image

7.5

Test run

After installation or inspection, carry out a test run:
1. Switch on the cooling systems.
2. Start up the machine without a load. To do this, close the circuit breaker and do not switch

off prematurely. Check whether it is running smoothly.

Switching the machine off again while it is starting up and still running at slow speed should

be kept to a bare minimum, for example for checking the direction of rotation or for checking

in general.

Allow the machine to run down before switching it on again.

3. If it runs perfectly, connect a load.
4. During the test run, check and document the following:

– Check whether it is running smoothly.
– Document the voltage, current and power values. As far as possible, document the

corresponding values of the driven machine.

– If this is possible using the available measuring equipment, check the bearing and stator

winding temperatures until they have reached steady-state values.

– Check the machine for noise or vibrations on the bearings or bearing shields as it runs.

5. In case of uneven running or abnormal noise, switch off the machine. As the machine runs

down, identify the cause.
– If the mechanical operation improves immediately after the machine is switched off, then

the cause is magnetic or electrical.

– If the mechanical running does not improve immediately after switching the machine off,

then the cause is mechanical.

- Imbalance of the electrical machine or the driven machine

- The machine set has not been adequately aligned

- The machine is being operated at the system resonance point. System = motor, base

frame, foundation, ...

NOTICE
Serious damage to the machine
If the vibration values in operation are not maintained in accordance with DIN ISO

10816-3, then the machine can be mechanically destroyed.
● During operation, observe the vibration values in accordance with DIN ISO 10816‑3.

Commissioning
7.5 Test run

SIMOTICS M-1PH8 1PH818., 1PH822., 1PH828.

92

Operating Instructions 10/2017

«
...
90
91
92
93
94
...
»

Summary of Contents for SIMOTICS M-1PH818



























































































































































































































































































































Reviews:

No comments

Related manuals for SIMOTICS M-1PH818

Brand: Schweigen Pages: 28

Brand: EBARA Pages: 36

MAESTRIA+ 50 io

Brand: SOMFY Pages: 112

Johnson BJ25E4SUC

Brand: BRP Pages: 265

Brand: Magnetic Pages: 24

Brand: Lenze Pages: 36

MCA10I40 Series

Brand: Lenze Pages: 44

Smart Motor m300

Brand: Lenze Pages: 116

Brand: Lenze Pages: 72

Brand: Toro Pages: 27

Brand: YS Pages: 2

Brand: Yanmar Pages: 70

TWINMOT T2-PLUS H

Brand: Germany Motions Pages: 12

Brand: Yanmar Pages: 84

Brand: Parker Hydraulics Pages: 32

Brand: O.S. engine Pages: 18

Brand: KRESS Pages: 46

Brand: Barrus Pages: 88

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands