Siemens SIMATIC TDC System Manual Download

Page: 84 / 228

CPU modules

4.1 CPU module CPU555

SIMATIC TDC hardware

System Manual, 08/2017, A5E01114865-AL

Table 4- 5

Operating states of the CPU555 during the firmware update

Display

Operating state

Initialization phase

LED test (approx. 1 sec)

●

Firmware start (flashing)

Operating system start

1...9

Operating system initialization / Startup

Update
F

Firmware update in progress (F flashing)

✓

Firmware update completed

4.1.9

Technical specifications/performance features

Note
CPU555 in the UR6021
The CPU module CPU555 can only be operated in the rack UR6021.
UR6021 can be equipped with a maximum of eight CPU555.

Article number

CPU module CPU555

6DD1600-0BB0

CPU

Processor

64-bit Intel CPU

Clock frequency

2 GHz

Communications processor

32-bit CPU

Clock frequency

450 MHz

Note
Removal and insertion
Removal and insertion of the module is not permitted during operation.

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Summary of Contents for SIMATIC TDC





































































































































































































































Search results

Summary of Contents for SIMATIC TDC

Reviews:

Related manuals for SIMATIC TDC

Brands by name

Popular brands

Siemens SIMATIC TDC, System Manual

Search results

Summary of Contents for SIMATIC TDC

Reviews:

Related manuals for SIMATIC TDC

Brands by name

Popular brands