Siemens SIMATIC RF1000 Series Operating Instructions Manual Download Page 66

Page: 66 / 77

Technical specifications

SIMATIC RF1000

Operating Instructions, 02/2020, C79000-G8976-C432-07

6GT2831-6xA50

Permitted ambient conditions
Ambient temperature

•

During operation

•

-25 ... +55 °C

•

During transportation and storage

•

-25 ... +55 °C

Minimum distance between two readers

15 cm

Degree of protection to EN 60529

In installed state:

front IP65;

rear IP20

Shock-resistant to EN 60721-3-7, Class 7 M2

300 m/s²

Vibration-resistant to EN 60721-3-7, Class 7 M2 50 m/s²

Design, dimensions and weights
Dimensions (W × H × D)

•

excl. card holder

•

90 × 62 × 23.5 mm

•

Incl. card holder

•

99 × 62 × 34.6 mm

•

Mounting opening

•

76.5 (± 0.3) × 48.5 (± 0.3) mm

Weight

approx. 120 g

Type of mounting

Door installation

•

4 x stud screws (slotted screws) M4 x 20;

Tightening torque

≤

0.5 Nm

•

4 x Torx screws (EJOT) T10 x 10;

Tightening torque

≤

1.5 Nm

•

Installation wall thickness 2-7 mm

Cable length reader

↔

communications module

1.8 m USB connecting cable

Display elements

•

LED, 3 colors

•

Acoustic signal

Approvals

CE, FCC, IC

ATEX

MTBF

28 years

Only in conjunction with the SIMATIC RF1040R reader as of product version "AS: A" and SIMATIC

RF1070R as of product version "AS: B", and SIMATIC RF1070R OEM as of product version "AS:

A".

The minimum distance can be lowered if, from an application point of view, it is permissible that a

transponder can also be read by an adjacent reader.

Only in conjunction with the SIMATIC RF1060R readers as of product version "AS: B" and

SIMATIC RF1070R as of product version "AS: C".

Summary of Contents for SIMATIC RF1000 Series














































































Search results

Summary of Contents for SIMATIC RF1000 Series

Reviews:

Related manuals for SIMATIC RF1000 Series

Brands by name

Popular brands

Siemens SIMATIC RF1000 Series, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC RF1000 Series

Reviews:

Related manuals for SIMATIC RF1000 Series

Brands by name

Popular brands