background image

Programming 

 

6.2 Programming via USB/RS232 interface (using DLL functions) 

 

SIMATIC RF1000 

38

 

Operating Instructions, 02/2020, C79000-G8976-C432-07 

6.2.1.15

 

Autoread_SetMode (called via "exec_comand") 

This function controls the "Autoread" functionality during runtime. The memory content of the 

cards that enter the antenna field of the reader is automatically read in "Autoread" mode 

without an explicit read job. You can specify in your reader configuration whether only the 

UID or also explicit memory areas should be read. The read data is output with the 

"Autoread_GetMessage" function. 
Note that in "Autoread" mode, the "vhl_select" function is automatically executed cyclically by 

the reader. If the "vhl_select" function is executed from the Demo application as well, this 

can result in the card not being recognized when it enters the antenna field of the reader 

because it was already read in "Autoread" mode. In addition, the mode is ended with the 

function call "vhl_select" in "Autoread" mode. Make sure that the "vhl_select" function is not 

executed in addition in "Autoread" mode. 
By activating/deactivating the "Autoread" function, the "MessageBuffer" is deleted. This 

ensures that no incorrect results are supplied by a subsequent call of the 

"Autoread_GetMessage" function when no card is located in the antenna field. 

Function call 

int  

brp_exec_comand( 

  int Handle, 

  byte devcode,  

  byte cmdcode, 

  byte * param, 

  byte param_len, 

  init timeout, 

  init * Status, 

  byte * resp, 

  int * resp_len, 

  init max_resp_len 

); 

Table 6- 17  Description of the parameters 

Parameter 

Description 

brp_exec_comand 

The parameter activates/deactivates the "Autoread" function. 

 

Handle  

The session key returned by the "brp_open_usb_session" or 

"brp_open_serial_session" function. 

devcode 

0x05 

cmdcode 

0x00 

param 

Buffer for the function parameters: 

 

0x00: The "Autoread" functionality is deactivated and VHL functions can 

be used. 

 

0x01: The "Autoread" functionality is permanently switched on. There is 

a permanent check as to whether a card is located in the antenna field. 

 

0x02: The "Autoread" functionality is executed once as soon as a card 

enters the antenna field. This is followed by a switch to VHL mode. The 

card identification is executed one more time with another call using the 

parameter value 0x02. 

Summary of Contents for SIMATIC RF1000 Series














































































Reviews: