manualshive.com logo in svg

Siemens SIMATIC Rack PC IL 40, Getting Started

Share
Download
Siemens SIMATIC Rack PC IL 40 Getting Started Download Page 23

Commissioning

SIMATIC Rack PC IL 40, Getting Started
A5E00171493-02

2-7

4.  Remove the CD-ROM from the drive after installation.

5.  Restart your PC.

Initial Startup

Note

The procedure below describes, as an example, the first commissioning of a
Rack PC IL with the operating system Windows 2000, German.

The start-up window of the operating system appears.

In case of new hardware, the dialog for hardware installation appears. Confirm the
hardware installation.

The start-up window of the operating system reappears. Select and confirm your
system settings. The Rack PC IL is booted.

After restart

•

 

the time zone must be set and

•

 

the license contract must be confirmed.

Confirm your settings – the system settings are updated now.

Then, the date/time dialog is opened. Enter the correct date/time, if necessary, and
confirm your settings.

Close Windows and restart the Rack PC to fully integrate the upgraded.

Summary of Contents for SIMATIC Rack PC IL 40









































Reviews:

No comments

Brands by name

Popular brands

Load more brands