Siemens SIMATIC NET RUGGEDCOM i800 Installation Manual Download Page 27 | Manualshive

Page: 27 / 38

background image

Communication Ports

The following is the pin-out for the RJ45 male connectors:

1

8

Figure 4.2

RJ45 Ethernet Port Pin

Configuration

Pin

Name

Description

1

RX+

Receive Data+

2

RX-

Receive Data-

3

TX+

Transmit Data+

4

Reserved (Do Not Connect)

5

Reserved (Do Not Connect)

6

TX-

Transmit Data-

7

Reserved (Do Not Connect)

8

Reserved (Do Not Connect)

For specifications on the available copper Ethernet ports, refer to

"Copper Ethernet

Port Specifications (Page 19)"

18

RUGGEDCOM i800

Installation Manual, 01/2021, C79000-G8976-1002-06

«
...
25
26
27
28
29
...
»

Summary of Contents for SIMATIC NET RUGGEDCOM i800







































Reviews:

No comments

Related manuals for SIMATIC NET RUGGEDCOM i800

SmartCell 6A000

Brand: Cabletron Systems Pages: 114

Brand: Cabletron Systems Pages: 62

CyberSWITCH CSX150

Brand: Cabletron Systems Pages: 49

Cabletron CyberSWITCH CSX5500

Brand: Cabletron Systems Pages: 729

COOPER POWER SERIES

Brand: Eaton Pages: 32

Brand: Keithley Pages: 452

DynaGST/2402G GEP-33224T-1

Brand: UNICOM Pages: 1

Cleveland Controls RSS-498-013

Brand: UNICONTROL Electronic Pages: 2

Brand: Gefen Pages: 31

Brand: ORiNG Pages: 2

TIMEGUARD WF10COM

Brand: Theben Pages: 35

Brand: West Mountain Radio Pages: 10

VH M 1 1 1 Series

Brand: Jlso Tec Trade Pages: 15

Brand: UNICOM Pages: 15

Brand: Maiwe Pages: 5

Brand: Zonet Pages: 7

GlobeCaster STUDIO 4000

Brand: Global Streams Pages: 144

TNM4000-TP36FF4X16G24P

Brand: MRD Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands