Siemens SIMATIC 6AV7861-1AA00-0AA0 Operating Instructions Manual Download | Manualshive

Page: 17 / 26

background image

Commissioning

3.4 Installing UPDD

Flat Panel
Operating Instructions (Compact), 09/2008, A5E02313712-01

19

3.4

Installing UPDD

3.4.1

Prerequisites

●

The commissioning engineer has administrator privileges.

●

The operating system is Windows 2000 SP 4, WinXp Pro Professional or

WinXP embedded Professional.

●

The program is exclusively provided for touch operation.

●

A USB keyboard and USB mouse are connected to the PC.

●

A previous version of the "UPDD" software must not have been installed.

3.4.2

Procedure

1.

If a previous version of the "UPDD" software is installed, please uninstall it. Subsequently

restart the computer.

Note
Use the application from the "Documentation & Drivers" CD supplied, or from the Internet.

You can find the application under .

2.

Start the software by double-clicking on "Setup".
The "UPDD Install" dialog box is displayed. This informs you of the software version and

of supported controllers.

Figure 3-1

Installing UPDD

3.

Click "Install" in order to install the program.

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

«
...
15
16
17
18
19
...
»

Summary of Contents for SIMATIC 6AV7861-1AA00-0AA0



























Reviews:

No comments

Related manuals for SIMATIC 6AV7861-1AA00-0AA0

Brand: ABB Pages: 36

Brand: ABB Pages: 40

Brand: Datavideo Pages: 50

Brand: Waterous Pages: 90

Brand: Campbell Pages: 14

Brand: Yamaha Pages: 50

Brand: A&D Pages: 30

Brand: ACCU-CHECK Pages: 104

Brand: IDEAL Networks Pages: 10

AquaPure Ei Series

Brand: Jandy Pages: 4

Brand: janitza Pages: 30

AquaPure Ei Series

Brand: Jandy Pages: 8

Jandy Pro Series

Brand: Jandy Pages: 16

Brand: M-system Pages: 3

Brand: M-system Pages: 5

Brand: MA Pages: 2

Brand: Pari Pages: 11

Brand: Pari Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands