Siemens SIMATIC 6AV7861-1AA00-0AA0 Operating Instructions Manual Download | Manualshive

Page: 12 / 26

background image

Unpack and connect the device

2.6 Connecting the Cables

Flat Panel

12

Operating Instructions (Compact), 09/2008, A5E02313712-01

2.6

Connecting the Cables

Introduction

The Flat panel and computer unit need to be connected by cable for data transmission.

Further information is available in the "Description" chapter of the operating instructions

under the section, "Accessories."

Procedure when the distance is ≤ 5 m

Connect the DVI or VGA cable to the Flat Panel and the computer unit.

Note
Use a USB cable for the Touch Screen versions.

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

«
...
10
11
12
13
14
...
»

Summary of Contents for SIMATIC 6AV7861-1AA00-0AA0



























Reviews:

No comments

Related manuals for SIMATIC 6AV7861-1AA00-0AA0

Relion 670 series

Brand: ABB Pages: 66

Brand: Napoleon Pages: 2

Brand: Raytheon Pages: 62

Brand: NEC Pages: 29

Brand: vanEE Pages: 52

Brand: Caddon Hives Pages: 3

Brand: CAE Healthcare Pages: 108

Brand: Cannon Pages: 36

Brand: MADRIX Pages: 12

Brand: Narcotrend Pages: 47

Brand: Eaton Pages: 4

Brand: Federal Signal Corporation Pages: 4

Brand: ParaBody Pages: 7

Brand: Ibiza Pages: 21

Brand: IBASE Technology Pages: 67

Brand: IBC Pages: 8

Brand: Ibanez Pages: 8

Brand: IAI Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands