Siemens SGT-400 Operator'S Manual Download Page 3

Page: 3 / 38

Turbine Package Operators Manual

Chapter 1

Turbine Package System Overview

1-3

Hydraulic Pump Boost Flow Oil Filter..................................................................................................................... 24

Starter Clutch ......................................................................................................................................................... 24

Turbine Underbase, Enclosure and Air Supply/Exhaust Systems............................................25

Introduction..............................................................................................................................................25

Underbase ................................................................................................................................................25

Turbine Acoustic Enclosure ...................................................................................................................25

Ventilation System...................................................................................................................................25

Dampers................................................................................................................................................................. 26

Ventilation Inlet and Outlet Silencers ..................................................................................................................... 26

Ventilation Inlet Filter – Inertial Type (if applicable)................................................................................................ 26

Ventilation Inlet Filter – Marine Type (if applicable) ............................................................................................... 26

Negative Pressure Ventilation Fan(s) (if applicable) .............................................................................................. 26

Positive Pressure Ventilation Fan(s) (if applicable)................................................................................................ 26

Instrumentation....................................................................................................................................................... 26

Combustion Air System ..........................................................................................................................27

Air Inlet Filter - Marine Type (if applicable)............................................................................................................ 27

Air Intake Filter - Pulse Type (if applicable)............................................................................................................ 27

Air Intake Silencer .................................................................................................................................................. 27

Acoustic Lagging.................................................................................................................................................... 28

Instrumentation....................................................................................................................................................... 28

Exhaust System .......................................................................................................................................28

Exhaust Silencer .................................................................................................................................................... 28

Acoustic and Thermal Lagging............................................................................................................................... 28

Instrumentation....................................................................................................................................................... 28

Fire & Gas Protection System......................................................................................................29

General Description.................................................................................................................................29

System Control and Operation ...............................................................................................................29

System Components ...............................................................................................................................29

Heat Detectors ....................................................................................................................................................... 29

Infra Red (IR) Flame Detectors .............................................................................................................................. 30

Gas Detectors ........................................................................................................................................................ 30

Ventilation Dampers............................................................................................................................................... 31

Extinguishant Bottles.............................................................................................................................................. 31

Instrumentation........................................................................................................................................31

Pressure Monitoring ............................................................................................................................................... 31

Position Monitoring................................................................................................................................................. 32

Gearbox and Generator ................................................................................................................33

Gearbox ....................................................................................................................................................33

Generator..................................................................................................................................................33

Cooling System ...................................................................................................................................................... 33

Generator Bearing Lubrication ............................................................................................................................... 33

Vibration Monitoring ............................................................................................................................................... 34

Generator Winding Temperature Monitoring.......................................................................................................... 34

Anti-condensation Heating ..................................................................................................................................... 34

Summary of Contents for SGT-400







































Search results

Summary of Contents for SGT-400

Reviews:

Related manuals for SGT-400

Brands by name

Popular brands

Siemens SGT-400, Operator'S Manual

Search results

Summary of Contents for SGT-400

Reviews:

Related manuals for SGT-400

Brands by name

Popular brands