Siemens SG035 Series, Owner'S Manual

Page: 47 / 64

1 026915 2 NIPPLE CLOSE 3/4 X 1.375
2 075580 1 FLANGE FUEL INLET
3 0F6390B 1 REGULATOR ASSY 2.4L
4 039253 2 SCREW HHC M8-1.25 X 20 G8.8
5 022145 2 WASHER FLAT 5/16-M8 ZINC
6 022129 2 WASHER LOCK M8-5/16
7 045771 2 NUT HEX M8-1.25 G8 CLEAR ZINC
8 040173 2 CLAMP HOSE #5.5 .62-.62
9 0E8286 1 STREET EL 45D 1/2 NPT BRASS
10 026812 2 ELBOW 90D 3/4 NPT
11 0F8379 1 NIPPLE PIPE 3/4 NPT X 7
12 0F3869 1 (REF) SWITCH PRESSURE GAS 5" RISE (INCLUDED WITH I/N 3)
13 057823 2 CLAMP HOSE #10 .56 - 1.06
14 059057 1 HOSE 3/4 ID SAE-30R2 (18” LG)
15 047527 1 BARBED STR 1/2 NPT X 3/4
16 0D1509 1 DECAL INLET PRESSURE
17 * 050279 1 DECAL FUEL INLET NG (NATURAL GAS APPLICATION)
050280 1 DECAL FUEL INLET LPG (LP VAPOR APPLICATION)
18 0F2119 1 O-RING 45.63 ID X 2.62 WIDTH
19 0E6586 1 GASKET BOSCH 32
20 0E4394 1 ACTUATOR BOSCH 40 GOVERNOR (45KW)
0E4395 1 ACTUATOR BOSCH 32 GOVERNOR (35KW)
21 040105 1 HOSE COOL 2 IN ID 20R4 (45KW)
057753B 1 HOSE 1.5 ID X 2 LG 20R4 (35KW)
22 0E6382B 1 VENTURI HOLDER W/40MM ACTUATOR (45KW)
0E6382C 1 VENTURI HOLDER W/32MM ACTUATOR (35KW)
23 0F7790E 1 VENTURI THROTTLE 26MM
24 0E7121 1 O-RING 47.625 ID X 2.38 WIDTH
25 089617 1 (REF) BARBED STR 1/4 NPT X 1/4 MALE
26 022097 4 WASHER LOCK M6-1/4
27 046580 4 SCREW SHC M6-1.0 X 45 G12.9
28 035685 2 CLAMP HOSE #28 1.32-2.25
29 0F6155 1 HARNESS CPL FUEL JUMPER
30 047290 1 HOSE 3/8 ID SINGLE BRAID (18” LG)
31 030340 1 HOSE 1/4 ID SAE 30R7 (12” LG)
32 057823 2 CLAMP HOSE #10 .56-1.06
NOTES:
1. REGULATOR (I/N 3) AS SHOWN IN ILLUSTRATION IS SET UP FOR
NATURAL GAS APPLICATION.
2. TO CONFIGURE REGULATOR FOR LP VAPOR, SWITCH HOSE BARB,
HOSE CLAMP (I/N 13) AND HOSE (I/N 14) FROM “OUT-1” TO “OUT-2”.
REPLACE PIPE PLUG FROM “OUT-2” TO “OUT-1”. USE PIPE SEALANT
ON HOSE BARB AND PIPE PLUG. MAKE SURE TO KEEP PORTS FREE
FROM DEBRIS DURING RECONFIGURATION PROCESS.
3*. FOR LP VAPOR APPLICATION SUBSTITUE LPG FUEL INLET DECAL P/N
050280 FOR NG FUEL INLET DECAL P/N 050279 (ITEM17).
4 . WHEN SWITCHING FUEL TYPES, THE PROPER DIP SWITCH SITTINGS
MUST BE MADE TO THE CONTROL PANEL. SEE OWNERS MANUAL, FUEL
SECTION FOR MORE DETAILS.