Siemens RUGGEDCOM RX1512 Installation Manual Download | Manualshive

Page: 19 / 52

background image

Installing the Device
2.5.1 Connecting Low DC Power

2.5.1

Connecting Low DC Power

To connect a low DC power supply to the device, do the following:

CAUTION

Electrical hazard – risk of damage to equipment

Do not connect AC power cables to a 12, 24 or 48 VDC power supply terminal block.

Damage to the power supply may occur.

CAUTION

Electrical hazard – risk of damage to equipment

In normal operation, the jumper between the chassis ground and surge ground ter-

minals must be installed for proper operation. Damage to the device may occur oth-

erwise. Removing the jumper may also void the warranty.

Note

The RUGGEDCOM RX1512 works with both positive VDC power supplies and negative

VDC power supplies.

Note

For information about how to safely test the dielectric strength of the device, refer to

"Testing Dielectric Strength (Page 12)"

.

10

RUGGEDCOM RX1512

Installation Manual, 07/2019, C79000-G8976-1057

«
...
17
18
19
20
21
...
»

Summary of Contents for RUGGEDCOM RX1512





















































Reviews:

No comments

Related manuals for RUGGEDCOM RX1512

Brand: VeEX Pages: 53

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands