background image

Document No. 125-1009 
Installation Instructions 
February 10, 2020 
 

Page 14 of 20

 

Siemens Industry, Inc. 

Table 8.  600 Series BACnet Configuration Parameters*.

 

Parameter 

Definition 

Display 

Value Range 

Default 

Extended Definition 

P601 

MS/TP MAC address 

MS--TP MAC 

0-255 

255 

MS/TP MAC address must be unique for the 
entire network 1 to 254.   
In systems that support and use Master Nodes 
valid range to use is from 1 to 127. 
In systems that support and are using auto 
discovery leave value at default 255  

NOTE: 

When integrating with APOGEE

®

, set 

this parameter to be a Master Node. 

P602 

Baud Rate  

BAUD RATE 

= Auto 

9.6 

= 9600  

19.2   =19200  
38.4   = 38400 
57.6  = 57600 
76.8   = 76800 
115.2  =115200 

A=Auto 

This parameter wil

l set the network’s baud rate. 

Auto value will match detected Baud Rate in 
systems that support and are using auto 
discovery leave value at default “A”  

P603 

Device Instance 

DEV ID 

0 - 4194303 

4194303 

Device Instance (unsigned integer 0-4194303) 
In systems that support and are using auto 
discovery leave value at default 4194303  

P604 

Max Master 

MAX MASTER 

1--127 

127 

Max Master 

P605 

Serial number 

SER NR 

Display Only 

Display 

Only 

Display Serial number, 10 digit hex, 
programmed in factory 

P606 

Max Info Frames  

MAX FRAME 

 1-- 10 

Max Info Frames 

 

 

CAUTION: 

 

* See the Energy Management System Network Plan before entering values in 
the RDY2000BN 600 Series BACnet Configuration Parameters. Incorrect values 
will prevent connection to the Energy Management System. 

Table 9.  700 Series BACnet Configuration Parameters

 

Parameter 

Definition 

Display 

Value Range 

Default 

Extended Definition 

P701 

Firmware 

FIRMWARE 

Display only 

Display only 

Display Firmware Version 

 

Summary of Contents for RDY2000BN





















Reviews: